P0497 Engine Trouble Code

When you check engine light came on code P0497 the reason should be . However your vehicle's manufacturer may have a different definition for the P0497 OBD-II Diagnostic Powertrain (P) Trouble Code. So you should chech it on our car models.

P0497 code can be about changing a broken oxygen sensor can lead to a busted catalytic convertor which can cost upwards of $1,300. Taking your vehicle into a service shop will cost you around $300 depending on the vehicle. But, an oxygen sensor is easy to replace on many vehicles and is detailed in the owner's manual PDF or in our website. If you know where this sensor is located, you only have to unclip the old oxygen sensor and replace it with a new sensor. Regardless of how you approach it, you should get this fixed right away.

P0497 Code Meaning :

The oxygen (02) sensors on your car measure the oxygen in the exhaust to determine how rich or lean the ratio of fuel and air are in the cylinders. Optimizing this mixture means better fuel economy and fewer exhaust emissions.

P0497 OBD-II Diagnostic Powertrain (P) Trouble Code Description

P0497 OBD-II Trouble Code The evaporative emission (EVAP) control system limits fuel vapors from escaping into the atmosphere. Fuel tank vapors are allowed to move from the fuel tank, due to pressure in the tank, through the v P0497 code. Fuel Temperature Sensor B Circuit Range/Performance and Cylinder 4 Contribution/Balance Fault causes most of code P0497.

Reason For P0497 Code

The reason of P0497 OBD-II Engine Trouble Code is Fuel Temperature Sensor B Circuit Range/Performance.

P0497 the main thing to check is to verify the operation of the VCT solenoid in the engine. You're looking for a sticking or stuck VCt solenoid valve caused by contamination. Refer to vehicle specific service repair manual to perform component tests for the VCT unit.

How To Repair P0497 Code

Before starting let's see P0497 repairing process steps:

• Qualified technicians will begin by using a scan tool to access P0497 code stored in the ECU.
• Technicians will note P0497 code present and any freeze frame data associated with them.
• After all, if you sure the engine trouble is finished, the code will be cleared.

As you idle at a light or before positioning your vehicle in gear and you see that your engine is starting to create strange sounds, switch your oil filter and also inspect the pressure regulator to attempt and adjust the error. If you struggle to start your vehicle and notice it fails to turn over right away, it can also indicate a defective fuel pressure regulator.

The computer installed in each fuel-injected vehicle has to be aware of two factors before it can solve the proper cold-start air/fuel compound: the engine coolant temperature and the exterior air temperature. Your symptoms are exactly the same to a faulty engine coolant temperature sensor (ECT). The computer is measuring an air/fuel compound that is excessively meager.

Sometimes P0497 code comes with P049700 code.

Diagnosis Of Engine Error OBD Code P0497

It's essential to diagnose this trouble code. Then are some way which a handyperson should follow for diagnosing the problem that started a P0497 trouble code to be stored

The first step is introductory and is about reacquiring all the canons that have been set. For this, the individual scanner will have to be plugged into the individual harborage of your vehicle. Make sure you indurate frame the data. Any canons that were set previous to the P0497 code will have to be sorted first, as they may have been the reason for the law to set in the first place. It's always good to rule that out.

The coming step is to run a introductory examination of all the electrical circuits, connectors, wiring etc for damages similar as becks, erosion, fraudulent legs etc. All of these will have to be repaired or replaced. After that's sorted, clear the canons and go on a test drive to see if it resets. In case it resets, you'll have to continue your opinion. Depending on your vehicle you may have a vacuum operated selector or a vacuum solenoid if it's electrically actuated. In the case of the former, a hand held vacuum pump will have to be used to testit.The purpose is to see if the internal stopcock is getting turned by the selector, motor or solenoid. In order to do this, a command can be transferred to the system with scanner or by driving the vehicle under the special conditions that will spark the system. While this is passing keep an eye on the checkup tool data for the result.